Jemmyblog

Home of all learning

12 Easy Tips on How to cook steak with cannabutter | Recipes, procedures |

How to cook steak with cannabutter

 

How to cook steak with Cannabutter | Easy cooking tips|

 

If you love a good steak, a good cannabutter steak, then be prepared for a experience with this recipe.
Preparing steaks with cannabutter is just made easy with these easy steps.
Read this article till the end to learn how to cool steak with cannabutter.
This recipe has very few steps with a short prep time and consistently delicious results every time.
  • Servings: 1 serving
  • Prep Time: 10 mins
  • Cook time: 5 mins
How to cook steak with cannabutter
Cannabutter with steak

Ingredients

  • A 1.5-pound rib-eye steak 1 1/2 inches thick
  • 1 tbsp olive oil, though you can alternatively use canola oil
  • 0.5 teaspoons of salt and pepper
    grind to desired dosage
  • 1 tsp Cannabutter
  • The suggested dose is 15 milligrams of THC per teaspoon, or 15 mg per serving.

Instructions – How to cook steak with cannabutter

  1. Heat the oven to 500 degrees Fahrenheit. Steak should be brought to room temperature.
  2. Place a frying pan on the stovetop over high heat for 5 minutes once the oven has heated up. The steak should be lightly oiled and salt should be sprinkled on both sides.
  3. Depending on your desire, grind some black pepper on.
  4. The steak should be placed right away in the center of the hot, dry frying pan. Cook without moving for 30 seconds.
  5. Top the cannabutter steak to be prepared with your preferred amount of cannabutter. With tongs, flip the steak, and cook for a further 30 seconds.
  6. Put the pan in the oven without delay and wait two minutes. After two minutes, flip the steak and continue cooking. (The timing is for a medium-rare steak; for a steak cooked to your preference, bake it for additional few minutes. Consequently, medium is 3 minutes each side, medium well is 4 minutes per side, etc.)
  7. After removing the steak from the pan, give it a 2-minute rest by covering it loosely with foil. Now that it’s ready, serve it. If desired, add a variety of garnishes.

 

 

Simple tip | How to make steak with cannabutter |

For a even more rich meal I usually lightly sear already boiled corn on the cob in frying pan that I used.
The cannabutter used in cooking the steak will also seep into the corn for extra deliciousness.

 

 

How to cook steak with cannabutter in a skillet

 

  1. When the Cannabutter is bubbling in the skillet, add your beef, which should be chopped into 2-inch pieces. Place this cut on the stove.
  2. After that, season your steak with salt, pepper, and any other seasonings you choose. Cook for 3-6 minutes on each side, or until done to your liking.
  3. Cook for an additional 2 minutes while continuously stirring.
  4. Use your basting brush to coat your grilled steaks with any leftover Cannabutter that is still in the pan.
  5. Depending on how done it is, let the steak rest for 5 to 10 minutes. Enjoy!

 

 

FAQs

  • Can you use cannabutter for steak?

For this dish, you won’t need a lot of ingredients: your preferred cannabutter steak cut (we recommend Top Sirloin or aFilet)

½ – ¾ cup of Cannabutter (Check the recipes and procedures above)

 

  • Is putting butter on steak good?

 

Butter adapts itself wonderfully to particular cuts and for people who like to be present carefully supervising the cooking, making it great for frequently basting a steak.

Being there and frequently basting makes it less likely that the butter will burn and lose its flavor.

 

  • What is the purpose of putting butter on steak?

The flavor of your steak can be greatly improved by adding butter. It is easy to use but powerful.

Steak butter is used to add flavor and make the steak more succulent. Your steak will taste luxurious if you use steak butter.

You like this post,share:)

Leave a Reply

Your email address will not be published.